ThermoWood Tulipwood Cladding

 

 

Board Lengths: 1.8m, 2.1m, 2.4m, 2.7m, 3m, 3.3m, 3.6m
Please contact us for other sizes

Tulipwood hardwood is sourced from the eastern side of North America and can also be found in some parts of China. The tulip tree itself exceeds heights of 100 feet and is a very light weight tree, however it is also a very strong tree. It is usually straight grained with a fine and even texture and can sometimes have an attractive blister figure.
 
Although it’s a hardwood product thanks to it’s light gravity and it’s plain texture, our Tulipwood cladding offers a long service life and ease of implementation with many different application methods.

 

30 Year Biological Life

100% Natural

High Quality

What is ThermoWood?

ThermoWood is a thermal modification procedure that preserves wood in its most natural and flawless state for a life-long journey. The “ThermoWood method” involves a carefully computer controlled heat and steam process up to 210 degrees C.

Besides the preservation, the ThermoWood process also causes certain chemical changes in wood. Not only does the color darken but the stability, decay resistance and insulation properties are largely increased after the process is complete.

The ThermoWood method, brand, and logo can only by the used by members of the International ThermoWood Association.

Fixing and Finishing Methods

Hidden Fixings:

You have the option of using our hidden cladding clip fixing with the Palma cladding profile. The hidden clip system allows you to display your cladding boards with no visual sight of screws in the boards. The additional advantage is that if you wish to modify the cladding elevation at a latter date you can remove the boards and re-use them.

 

Finishing Brad nails:

Because the Thermowood Cladding is stable and does not cup or twist you can use Stainless Steel Finishing brad nail/pins and depending on the profile you choose, these can be fixed into the profile at an angle of 45 degrees. If you are unsure of the holding strength of a 50mm pin, a bead of flexible silicone can be applied to the batten prior to fixing each cladding board. This will give you a clean appearance to the surface of your timber cladding as they virtually disappear from view. 

Face Fixings:

Standard practise has always been to screw or nail through the face of the cladding which is unsightly and can split the timber. If you wish to do so simply pre-drill stainless screws through the face of the board into the sub-frame to avoid damaging the boards.

 

Board Spacing:

This will be created regardless of the profile you choose to go with. Do not ram the boards together tightly when fixing so that you allow for any minor movements that can occur with the changes in UK climate. Allowing approximately 1mm will be sufficient for most circumstances.

 

Cladding Batten Spacing:

We recommend 400mm centre to centre spacing for a standard area, projects may vary.

 

End Grain Sealer:

When the timber starts to dry out it loses the moisture quicker through the ends of the timber hence the characteristics of grain checking and opening up. Clear wax sealer seals the timber ends and slows down the moisture loss to a more controlled process, thus preventing this cracking. This is especially useful because cutting off the damaged ends not only becomes an expensive waste of timber, but may mean the difference between having the right length of timber for your project or it being several centimetres too short.

We recommend using our Messmers End Grain Wax Sealer to prevent the boards from grain checking.

 

Oil Finish:

Oiling the boards will help you to retain the dark rich colours within the boards. This product contains UV filters to delay the silvering process that strong sunlight causes in all timbers. We can now provide you with two options when it comes to oiling your boards, you can purchase our Messmers UV Plus Oil or you can order your boards pre-oiled saving you the initial labour cost of applying it yourself. If after a year you wish to maintain your investment we can supply the Clean & Oil starter Pack for you to use when convenient.

Delivery

​Confirmation of access for a large delivery vehicle
Someone on-site to accept and help our driver offload the order
Please note you need to give all possible details of the delivery address (Including complications)
Any Damaged or Missing items need to be reported to QTD within 24 hours

Get In Touch!

We’d love to hear from you; whether you have a question, have a query or a project in mind, we’d love to know! Please use our contact form below or if you would like to talk to us,
call on: 0118 373 2212